CY7C65215-32LTXIT Serial Port Access Issue
Forums: USB Full-Speed PeripheralsI have CY7C65215-32LTXIT development kit. I configured the device using "Cypress USB-Serial Configuration Utility" and I downloaded configuration file. Then I loaded...
View ArticleSend a ECG signal to PIC18F4550 to computer using the USB and its receipt by...
Forums: USB Full-Speed PeripheralshelloI'm using an appropriate protocol for USB send a signal to the computer to do. If the hex file the appropriate protocol (eg. Balk protocol) or you can provide me...
View ArticleProblem in using EP1IN and EP1OUT in FX2LP
Forums: USB Full-Speed PeripheralsAs suggested in one of the post here that EP1IN and EP1OUT cannot be used at the same time.I'm confused like why TRM of FX2LP has mentioned both endpoints separately...
View Articleconnect Qt with fpga
Forums: USB Full-Speed PeripheralsHi allI for connection Qt with FPGA want to use cypress usb controller , now I can use driver cypress for connect Qt with FPGA or no?if yes, any one have a example in...
View ArticleHow to prevent this situation ？
Forums: USB Full-Speed Peripherals hey: every big shot. recently i've got some new question with my fx2lp board(slave fifo, internal clock^-^). every single time after i download my firmware into my...
View ArticleCY7C65211A I2C modes
Forums: USB Full-Speed PeripheralsHas anyone tried using the CY7C65211A as a I2C slave in VCP mode? I want to write data to it from a PSoC4 and have it behave as if it were in UART mode (ie....
View ArticleConfiguring Endpoint for OUT bulk transfer
Forums: USB Full-Speed PeripheralsHello,I want send any number of bytes from host PC to the endpoint of FX2LP in full speed mode.My doubts are:1. How can I configure the endpoints or registers so that...
View ArticleInterfacing an EC using CCGx
Forums: USB Full-Speed PeripheralsHi!We are trying to integrate the CCG3 (using the CY4531 kit) with an embedded controller (EC) so that we can interact with the PD-negotiation process. However, we...
View Articlemigrate to cyusb3 from ezusb
Forums: USB Full-Speed PeripheralsHi,Our company has a custom hardware that uses the CY7C64713-128AXC how can I update the ezusb to cyusb3? I am confused on what sdk i need i see EZ-USB FX3 Software...
View ArticleWhere can I find design examples of CY7C67200?
Forums: USB Full-Speed PeripheralsThe http://www.cypress.com/part/cy7c67200-48baxi contains a lot of information about the CY7C67200 but no simple example designs except a complex example for which no...
View ArticleCyAPI Host not reading bytes
Forums: USB Full-Speed PeripheralsI am getting started on CyAPI and used the loopback example program as the starting point.The device appears to receive the data from the host PC but when it goes to...
View ArticleClik here to view.
4 endpoint in slave sync fifo 2 bit
Forums: USB Full-Speed Peripheralshi I have this code for 4 endpoint, but i cant send data from fpga to fx3.I can send data by an endpoint to fx3 but with another endpoint I cant.What is the...
View ArticleI2C Write on EZ-USB FX (original one)
Forums: USB Full-Speed PeripheralsI am trying to make some changes to the firmware of a device. It uses an EZ-USB FX with a serial eeprom (24lc02)The firmware is uploaded via USB control A0The original...
View Article4 endpoint in slave sync fifo
Forums: USB Full-Speed PeripheralsHiI want have a firmware with 4 endpoints. Can I have an example in slave fifo sync by 4 endpoints?Thanks
View ArticleHave all source code, but have no idea what to do.
Forums: USB Full-Speed PeripheralsWell the Engineer who wrote all the code for our product is no longer with us. Since 32 bit windows are but a thing of the past I am stuck trying to figure out how to...
View ArticleLong shot to solve exceptional operator error on CY7C65215
Forums: USB Full-Speed PeripheralsHello,Is there any pin muxing capability on the CY7C65215 for the TX and RX pins? Just in case some electrical engineer happens to connect the TX and RX backward and...
View ArticleA quenstion about CY7C64215
Forums: USB Full-Speed PeripheralsHi, I want to use cy7c64215 as a HID device like keyboard, but the command will be send by I2C from another mcu as master to cy7c64215 as slave. When the cy7c64215...
View ArticleUSB Bulk transfer on HID class FM4 Core
Forums: USB Full-Speed PeripheralsHello,I am developing a device using s6e2cc core and USB1 device feature. My device will replace an older one, that has USB connection with PC using HID class and a...
View ArticleInterfacing an EC using CCGx
Forums: USB Full-Speed PeripheralsHi!We are trying to integrate the CCG3 (using the CY4531 kit) with an embedded controller (EC) so that we can interact with the PD-negotiation process. However, we...
View ArticleLinux Api CyOpen not working under CDC Mode for CY7C65211
Forums: USB Full-Speed PeripheralsHi all,I've install the SO library into my raspberry pi and device able to detect after i plug it in to usb port. However when i try to turn on one of the GPIO pin, my...
View Article